Data Center Flooring
Floors, linings and coatings for data centers, from the data hall to the generator yard, installed around live operations.
What Flooring Does a Data Center Need?
A data center has many floor types under one roof. Data halls need flat, dust-free concrete. Electrical rooms need static control. Battery rooms, generators and fuel tanks need floors and linings that keep spills contained.
We cover all of it, plus offices, docks and stairs, so you have one flooring team for the campus. Work is phased with night and weekend crews so critical rooms stay online.
Legacy Industrial Coatings installs commercial and industrial epoxy flooring, polished concrete and floor coatings from Plano, Texas, across Dallas–Fort Worth, all of Texas and nationwide. See our commercial and industrial epoxy flooring and polished concrete pages.
Serving Dallas, Fort Worth, Plano, Frisco, McKinney, Richardson, Carrollton, Lewisville and the rest of North Texas, plus Houston, Austin, San Antonio and projects across Texas and nationwide.
Where We Work in a Data Center
Data halls
Densified and sealed concrete with joint fill, or thin static-dissipative epoxy where your spec calls for it.
Electrical and UPS rooms
Static-control epoxy that protects sensitive equipment from discharge.
Battery rooms
Acid-resistant novolac epoxy with cove base and coated curbs to contain spills.
Generators and fuel containment
Oil- and diesel-resistant floors and linings for generator rooms, tank dikes and transformer pits.
Cooling and mechanical rooms
Seamless urethane cement or epoxy with cove base that holds water and glycol.
Offices, NOC and lobbies
Polished concrete, carpet tile, LVT or decorative quartz for the people side of the campus.
Before & After
Transformer containment pit at an Irving, TX data center, before and after a watertight coating.
On the Job
Specs & Data Sheets
Static-Control Systems We Install
For data halls, electrical rooms and electronics lines we install Sherwin-Williams Resuflor static-control flooring. System overviews, application instructions and guide specs are below.
Resuflor Topcoat SDU
A nominal 20 mil static-dissipative epoxy and urethane system. Per the manufacturer, it tests at 1×10⁵ to 1×10⁹ ohms under ANSI/ESD S20.20 with body voltage under 100 volts.
Resuflor Topcoat SD
A thin-mil static-control epoxy topcoat with a stipple finish. Conductive over a conductive primer, static-dissipative over a standard epoxy primer.
Resuflor Deco Flake SD
A high-gloss, static-dissipative flake floor: vinyl chips in an epoxy base, sealed with an abrasion-resistant polyurethane.
FAQ
Data Center Flooring Questions
Do data halls need ESD flooring?
Not always. Most data halls do well with densified and sealed concrete and filled joints. Static-dissipative epoxy is usually specified in electrical and UPS rooms, and in halls where the operator's standards call for it. We install both.
Can you line fuel and transformer oil containment?
Yes. We line diesel tank dikes and transformer pits with coatings that keep oil and fuel from soaking into the concrete, so the containment does its job. Curbs, walls and penetrations are coated as part of the same lining.
Can you work in a live facility?
Yes. We phase work zone by zone, run night and weekend crews, and coordinate with your operations team so critical rooms stay online. Dust control and containment are planned around sensitive equipment before work starts.
What drives the cost of data center flooring?
The number of room types, square footage, static-control and containment requirements, slab condition, and phasing around live operations. Send us your plans for a full bid within 24 hours, or request a site walk within 1 to 3 business days.
Get a bid on your data center floors
Send plans or a scope. Site walk within 1–3 business days; full bid within 24 hours of receiving plans.
Request Information
Tell us about your project and we'll follow up within one business day.
Prefer to talk now? Call (214) 305-6516 or